You don't need a 20-foot dish to do real radio astronomy. Here are three ways in, all used by amateurs in the last two years: catch the Sun with an 18-inch TV dish, hear the hydrogen of the Milky Way, or start free with a telescope you control online.
The Sun in radio today—Loading today's measurement…
Based on the Itty Bitty Telescope, designed by the late Chuck Forster, a CVAS member and a member of the Society of Amateur Radio Astronomers (SARA), and later improved by SARA member Kerry Smith. NRAO still uses it with schools. The original read the Sun on a satellite-finder meter; that meter (Channel Master 1004IF) is no longer made, so this version records the Sun on a computer with a $38 USB radio instead.
The dish focuses radio waves onto the LNB (low-noise block converter), which amplifies the 12.2–12.7 GHz satellite band and shifts it down to 950–1450 MHz for ordinary coax (RTL-SDR.com). The USB radio measures how much power arrives: anything warm in front of the dish raises it. The original Itty Bitty Telescope powered its LNB with 12 V from eight AA cells; satellite LNBs are normally fed 13 or 18 V up the coax, which a satellite power inserter does. The radio's own 4.5 V bias tee is too weak for an LNB, so leave it off, and the DC block keeps the LNB voltage out of the radio.
What you need
18-inch satellite TV dish with its LNB and mount
NRAO used a DirecTV 18-inch dish. Used ones are often free.
RTL-SDR Blog V4L USB radio
$37.95 (rtl-sdr.com). Released August 2026 after the V4 sold out.
Satellite power inserter with its supply
Puts 13–18 V on the coax for the LNB
Inline DC block
Protects the radio from the LNB voltage
75-ohm coax with F connectors, F-to-SMA adapter
The radio has an SMA socket
75-ohm terminators
One for each unused LNB output
A base that swivels
30 × 30 in board, a lazy Susan, screws and glue
Laptop
Windows, Mac or Linux
Build it
Make the base. Centre the lazy Susan on the board, glue and screw it, and bolt the dish bracket to the turning top so the dish can swing and tilt. Make it heavy enough not to tip.
Prepare the dish. Put a 75-ohm terminator on every LNB output except one, and run coax from that output.
Connect. LNB coax → the inserter's dish/LNB port; the inserter's receiver port → DC block → adapter → radio → laptop. Plug in the inserter.
Install the software. Follow the RTL-SDR quick-start guide (the V4-series radios need the RTL-SDR Blog drivers). Turn automatic gain off and set a fixed gain.
Log the power. The free rtl_power tool writes power to a spreadsheet file every few seconds, for example rtl_power -f 1150M:1250M:1M -i 2 -g 20 sun.csv. Or watch the noise floor rise in SDR#.
Find the Sun
Never look at the Sun, with or without anything in front of your eyes.
Read empty sky first. Point at clear sky away from the Sun, trees and buildings. Note the power.
Aim by shadow. Turn and tilt until the LNB's shadow falls in the middle of the dish. The power rises as you get close.
Peak it. Small moves until the power is highest: you are on the Sun.
Let the Earth turn. Swing a little west of the Sun and leave it. The Sun drifts through in about 15 minutes today, and your log shows a smooth hill.
Today's numbers for an 18-inch dish
Beam width at 12.45 GHz (2.41 cm): about 3.7° (≈ 70 λ / D). The Sun is 0.53° across.
Sun's radio brightness at 12.45 GHz today: —, worked out from NOAA's measurements at 8.8 and 15.4 GHz.
Signal the Sun adds: — (antenna temperature, T = η A S / 2k with 50% efficiency).
A tree or a person that fills the beam is about 300 K, which is why the Itty Bitty manual notes trees read stronger than the Sun.
Drift time today: —, at the Sun's declination of —.
Track 2
Hear the Milky Way
Cold hydrogen gas between the stars glows at 1420.4 MHz (21 cm). Point a small dish or horn straight up and let the Earth turn: when the Milky Way passes overhead, the hydrogen appears as a bump in the spectrum, shifted by the gas's motion. IEEE Spectrum's David Schneider used those shifts from a homemade horn to measure how the galaxy rotates, matching professional results.
Ready-made: Discovery Dish
$311.95
Discovery Dish, 70 cm (KrakenRF)
$149
Hydrogen-line feed, amplifier and filter built in, 6 m coax
$125
RTL-SDR Blog V4L (powers the feed through its bias tee)
$37.95
Mast or tripod
your own
Beam about 21°; the Sun takes — to drift through today. In February 2026 Dr. Kamal Jabbour mapped the Milky Way's hydrogen with one on a motorized mount, and caught a solar flare.
A 1 m grid dish has a beam about 15°. Tip: in December 2025 Alex P found the Discovery Dish feed on a 1 m Wi-Fi grid dish clearly beat a standard feed with a separate amplifier.
At 1420 MHz the radio waves are 21 cm (8.3 in) long, so a homemade dish does not need to be very precise. The SETI League's rules: the surface may stray up to a tenth of a wavelength (about 2 cm) from the true curve, and mesh holes up to an eighth of a wavelength (about 2.6 cm) still reflect well (accuracy, mesh). That is woodworking accuracy.
Simplest: a horn, no dish at all
A weekend
A pyramidal horn made of foil-covered foam board or aluminium flashing, with the SAWbird+ H1 and RTL-SDR at its back. Its beam is wider and the signal smaller than a dish's, but the Milky Way's hydrogen still shows up clearly.
Pick a size in the calculator. It prints the curve for your ribs.
Cut 8 to 12 ribs from plywood or aluminium flat bar. Mark each height from the table, join the marks with a flexible strip of wood, and cut along it.
Mount the ribs on a round hub like bicycle spokes, and tie their tips together with a rim ring so the shape can't twist.
Cover with ½-inch hardware cloth (1.27 cm holes, well under the 2.6 cm limit). Fasten it to every rib with zip ties or rivets, overlap the seams and keep it tight.
Make the feed from a metal can or 6-inch duct with an end cap (sizes in the calculator), and hold it at the focus on three struts, its open end facing the dish.
Anchor it. A dish is a sail: bolt the mount down before the first windy day.
Dish and feed calculator
Rib heights (measured up from the centre of the dish)
Feed can
Parabola: height = r² ÷ (4 × focal length). Beam ≈ 70 λ/D; gain and Sun signal assume 50% efficiency. Can limits are where the circular waveguide carries only its first mode (TE11 starts at λ/1.706, TM01 at λ/1.306). Probe position is a quarter of the guide wavelength from the closed end; where the focus sits inside the can uses the SETI League feed formula, whose 1420 MHz feed is 15.6 cm wide with a 4.6 cm probe 8.8 cm from the back.
Which radio? RTL-SDR or Airspy Mini
RTL-SDR Blog V4L
Airspy Mini
Price
$37.95
$99 (Airspy store) to $165
Hydrogen-line sensitivity
The same: behind a 40 dB amplifier the radio adds under 0.2 K of noise
Spectrum seen at once
2.4 MHz · ±253 km/s
about 5 MHz · ±528 km/s
Converter
8-bit
12-bit, better with strong interference
Clock
1 ppm (0.30 km/s)
0.5 ppm (0.15 km/s)
Powers the amplifier?
Yes, 4.5 V bias tee
4.5 V but only 50 mA: power the SAWbird (120 mA) from its USB port
Start with the RTL-SDR. Step up to the Airspy Mini for wider, cleaner baselines and smoother drift scans (1.4–1.6× less noise in the same time). Sources: Airspy, Airspy quick start, Nooelec.
Observe it
Point straight up on a mast with a clear view, away from Wi-Fi routers and cell towers.
Record a reference. Average a few minutes of spectrum on empty sky (or with the feed covered) to subtract later.
Average and watch. With the Milky Way overhead, the hydrogen bump rises near 1420.4 MHz. Tonight's best times are at the top of this page.
Free software: SDR# with the IF Average plugin (Windows), Virgo (open source), ezRA (open source), or GNU Radio.
Track 3
Start free
Online telescope
PICTOR
A 1.5 m radio telescope (1300–1700 MHz) that anyone can use free over the web, including for the hydrogen line.